Kiln Specifications at 1st Sept 2018.....................................................................................................................................................
Click here for a list of weights and external dimensions
 |
 |
 |
Tetlow K2 Front Load fitted with Parallelogram door and SR92 Temperature Controller |
Tetlow K4A Front Load fitted with SR92 Temperature Controller |
Tetlow K6 Front Load fitted with SR92 Temperature Controller |
NOTE: ALL UNITS CONNECT WITH NEUTRAL
MODEL |
PHASE |
VOLTS |
AMPS |
KW |
TEMP°C |
K2 FL |
1 |
240 |
10 |
2.4 |
1200°C |
K2 FL |
1 |
240 |
15 |
3.6 |
1280°C |
K4 FL |
1 |
240 |
10 |
2.4 |
1100°C |
K4 FL |
1 |
240 |
15 |
3.6 |
1280°C |
K4A FL |
1 |
240 |
10 |
2.4 |
1100°C |
K4A FL |
1 |
240 |
15 |
3.6 |
1280°C |
K5 TL |
1 |
240 |
15 |
3.6 |
1280°C |
K6 FL/TL |
1 |
240 |
15 |
3.6 |
1100°C |
K6 FL/TL |
1 |
240 |
20 |
4.8 |
1280°C |
K6 FL |
1 |
240 |
25 |
6 |
1280°C |
K6 TL |
2 |
415 |
10 |
4.8 |
1280°C |
K7 MW FL |
1 |
240 |
20 |
4.8 |
1100°C |
K7 MW FL |
1 |
240 |
30 |
7.2 |
1280°C |
K7 MW FL |
2 |
415 |
15 |
7.2 |
1280°C |
K7 MW FL |
3 |
415 |
10 |
7.2 |
1280°C |
K7 TL |
3 |
415 |
10 |
7.2 |
1280°C |
K8 TL |
3 |
415 |
15 |
10.8 |
1280°C |
K8B FL |
3 |
415 |
15 |
10.8 |
1280°C |
K9 FL/TL |
3 |
415 |
20 |
14.4 |
1280°C |
K10 FL/TL |
3 |
415 |
23 |
16.5 |
1280°C |
K11 TL |
3 |
415 |
25 |
18 |
1280°C |
K11A FL |
3 |
415 |
25 |
18 |
1280°C |
K12 FL/TL |
3 |
415 |
28 |
20.16 |
1280°C |
K12A FL |
3 |
415 |
40 |
28.8 |
1280°C |
K13 FL |
3 |
415 |
42 |
31 |
1280°C |
Please note: For extensive 1280°C/stoneware, we can supply K6 as 240V/25amp, for extended operating life of elements, requires direct wiring or 30amp plug top and lead (not supplied).
It is recommended that circuit breakers or fuses are electrical cables are rated at a minimum of 20% above the required amperage of the unit. Three phase kilns are 5 wire – 1 earth, 1 neutral, 3 actives.
Note: We can manufacture quite a number of 2 and 3 phase kilns as single phase if you have adequate single phase power available. The same may also be done with the multi-sided octagonal kilns.
 |
 |
 |
Tetlow K7 M/W fitted with No 3 Roof Vent System complete with Stand |
Tetlow K9 Front Load |
Tetlow K12A Front Load with Single Zone Flush Mount Harco Programmable Temperature Controller |
It is recommended that circuit breakers or fuses and electrical cables are rated at a minimum of 20% above the required amperage of the unit.
Three phase kilns are 5 wire – 1 earth, 1 neutral, 3 actives.
Note: We can manufacture quite a number of 2 and 3 phase kilns as single phase if you have adequate single phase power available. The same may also be done with the multi-sided octagonal kilns.
Tetlow Furnaces feature heavy gauge, mild and stainless steel cases for improved strength. Simple designs utilise rugged components and high quality materials to assure long trouble-free service.
The heating element is the heart of the electric furnace and contributes in three important ways. Heat up response, Chamber uniformity and element life. Element support is crucial for long element life. The open coil design is used to minimise temperature gradients between wire and chamber temperature. The size and temperature of your furnace will dictate element type and design.
Control is the brain of any furnace and determines the efficiency of the furnace operation. Tetlow furnaces are available with a wide variety of both automatic and manual controls to match your specific requirements. From manual percentage input control, to automatic digital programmers where control accuracy is a must.
The quality of the insulation is the single most important ingredient determining the efficiency and workability of any furnace. Tetlow offers the finest hot face insulating materials available today.
Specifications subject to change without notification.
